|
Stability Chamber Technical Specification
- Temperature Range: 20 oC to 60 oC
- Temperature Accuracy : + 0.2 oC
- Temperature Uniformity : + 1 oC
- Humidity Range: 40% Rh to 90% Rh
- Humidity Accuracy: + 2 % Rh
-
- Humidity Uniformity: + 3 % Rh
|
Standard Model (S)
|
Inside S.S. 304 with mirror polish & outside mild steel powder coated.
|
|
GMP Model (G)
|
Inside S.S. 316 with mirror polish & outside stainless steel 304 with dull buff finish.
|
Specification
- Double walled construction with backside triple.
- 3" Thick PUF Insulation ensures stable temperature with humidity & reduced energy consumption.
- Motorized Blower at back side of the chamber develops unique air flow system which ensures maximum uniform temperature & humidity condition inside the chamber.Unique air flow assures quick recovery after door openings.
- 1/12 HP, TEFC, F-class insulation, Single phase, 1440 RPM, 230 Volts
- High quality U shape S.S. Tubular Heaters are used for better heating.
- Steam injection system (Non condensing type) & reservoir tank with water level arrangement with indicator.
- Temperature Control
- Temperature Control: By means of Imported Microprocessor based auto tuned PID controller with CE mark & dual display of set value & process value.
-
Humidity Control
- Humidity Control & Sensing: By means of Imported Microprocessor based auto tuned PID controller with CE mark & dual display of set value & process value with direct % RH.Direct RH electronic capacitor type humidity sensor, avoid wick cup & water.
-
Safety Features
- Additional Safety thermostat to cut of dry heater supply in case temperature of overshoot.
- Float switch to cutoff the wet heater supply in case of low water level. Audio & Visual alarm.
- Compressor ON delay timer (2 min.) to safe guard the compressor.
- In built over load protector provided for hermetically sealed compressor.
-
Refrigeration System
- Refrigeration by means of CFC Free hermitically sealed Emerson Copland make compressor with R 134A for better cooling with ECO friendly refrigerant with time delay to safe guard compressor system.
- 50 mm validation port hole with silicon rubber seal to insert sensors for validation.
- Full view observation Acrylic door with gasket to observe sample inside the chamber.
- Interior illumination for Working area
- Specially designed stainless steel rod trays ensure uniform temperature distribution.
|
Models (S) or (G)
|
Capacity Liters
|
Internal size H x W x D cm
|
Trays
|
|
TI - 710 S / G
|
100
|
50 x 50 x 40
|
2
|
|
TI - 711 S / G
|
170
|
70 x 60 x 40
|
2
|
|
TI - 712 S / G
|
200
|
60 x 60 x 60
|
2
|
|
TI - 713 S / G
|
285
|
80 x 60 x 60
|
3
|
|
TI - 714 S / G
|
325
|
90 x 60 x 60
|
4
|
|
TI - 715 S / G
|
400
|
110 x 60 x 60
|
4
|
|
TI - 716 S / G
|
600
|
125 x 70 x 70
|
4
|
|
TI - 717 S / G
|
800
|
125 x 80 x 80
|
5
|
|
TI - 718 S / G
|
1000
|
157 x 80 x 80
|
5
|
|
TI - 719 S / G
|
1500 Double Door
|
146 x 150 x 69
|
10
|
|
TI - 720 S / G
|
2000 Double Door
|
146 x 150 x 92
|
10
|
Note: Two blowers for 400 ltrs to 2000 ltrs. Capacity chambers
|
